엔진 동력계 시험실에서의 산소 모니터링
Exhaust & Combustion Oxygen Analysis for Engine Performance Testing — OMD-190
Engine dynamometer testing evaluates engine performance, efficiency, and emissions under controlled operating conditions. Exhaust oxygen concentration is an important measurement parameter that helps engineers assess combustion conditions, evaluate excess air, and identify changes in engine operation across different loads and speeds.
When combined with measurements such as fuel consumption, exhaust gas composition, and engine operating parameters, oxygen data supports engine calibration, combustion analysis, and emissions development testing.
The OMD-190 process oxygen analyzer provides continuous oxygen concentration measurement in compatible, properly conditioned exhaust gas samples. By monitoring oxygen levels throughout dynamometer test runs, the analyzer helps engineers evaluate combustion trends and document test conditions.
- Dyno Test Cell QC
- Combustion Oxygen Analysis
- Engine Calibration Support
- 연속 공정 모니터링
Why Test Cell Oxygen Monitoring Matters
Exhaust oxygen concentration provides valuable information about combustion conditions at different engine operating points. Changes in oxygen levels can help engineers evaluate excess air, investigate air-fuel mixture variations, and assess combustion behavior during dynamometer testing.
When combined with fuel consumption, exhaust emissions, and other engine operating data, continuous oxygen measurement supports engine calibration, combustion strategy development, and performance troubleshooting.
Repeatable oxygen measurements throughout the test cycle also help engineers compare operating conditions and identify trends between successive test runs.
Where It's Used
- Engine calibration testing tracking exhaust oxygen across varying load and speed points
- Combustion efficiency analysis supporting air-fuel ratio tuning and diagnostics
- New engine development testing providing consistent oxygen data across development cycles
- Emissions development test cells supporting broader exhaust gas analysis alongside other measurements
Recommended Analyzer
The OMD-190 process oxygen analyzer provides stable, continuous oxygen concentration measurement for compatible engine dynamometer exhaust monitoring applications.
Connected to an appropriately designed exhaust gas sampling and conditioning system, the OMD-190 measures oxygen concentration in a representative sample collected from the engine exhaust stream.
The analyzer’s measurement output can be integrated with compatible test cell data acquisition systems, allowing engineers to record oxygen concentration alongside engine speed, load, fuel consumption, and other exhaust gas measurements throughout testing.
Proper sample cooling, filtration, and gas compatibility evaluation are essential for reliable measurement performance.
- 연속 공정 모니터링
- Fast Response
- 4-20 mA Output
- Panel Mount Enclosure with Remote Sensor
주요 사양
- Range: 0 – 25% O2, covering the typical range of engine exhaust oxygen content
- Response time: fast enough to track oxygen changes across varying engine operating points
- Sensor technology: process-grade sensor suited to continuous test cell duty
- Output: 4-20 mA for integration with test cell data acquisition systems
- Enclosure: rugged housing suited to dynamometer test cell environments
자주 묻는 질문
Exhaust oxygen concentration generally increases as an engine operates with a leaner air-fuel mixture because more oxygen remains after combustion. Near stoichiometric conditions, residual oxygen is typically low, although actual readings depend on combustion conditions, engine design, and exhaust sampling location.
Continuous oxygen measurement helps engineers identify changes in excess air and evaluate combustion trends during dynamometer testing.
However, oxygen concentration alone cannot accurately determine air-fuel ratio or lambda under all operating conditions. Dedicated lambda sensors or additional exhaust gas measurements are typically used when precise air-fuel ratio determination is required.
Yes. The OMD-190 provides a 4–20 mA analog output that can be connected to compatible engine dynamometer data acquisition and control systems.
This allows oxygen concentration measurements to be recorded alongside engine speed, load, fuel consumption, and other test parameters. Continuous data collection helps engineers evaluate combustion trends, compare test runs, and document operating conditions.
The receiving system must be configured to interpret the analog signal according to the analyzer’s selected oxygen measurement range.
Yes. The OMD-190 can be used for engine calibration, performance evaluation, and development testing where continuous oxygen concentration measurement is required.
The analyzer can help engineers monitor exhaust oxygen trends across different engine speeds, loads, and operating conditions. An appropriately designed sampling system must cool and condition the exhaust gas, and sensor compatibility with the expected gas composition must be verified.
The OMD-190 is intended for process oxygen measurement and should not be considered a substitute for specialized emissions certification equipment or dedicated air-fuel ratio measurement systems.
NEED HELP SPECIFYING AN ANALYZER FOR YOUR OPERATION?
Our application engineers can help confirm the right model for your process conditions.
English 
German 
Chinese 
Spanish 
Japanese 
Russian 
Portuguese 
French 
Vietnamese 
Korean 
Turkish 
Italian 
Arabic 
Ukrainian